OPPO Reno 14 Firmware Download CPH2739_11_A.26 - CPH2739 Android 16 Stock ROM
OPPO Reno 14 | CPH2739 | Updated November 2026

A soft bricked Reno 14 is rarely dead. In most cases the hardware is fine and only the system partition needs to be written again with a signed Android 16 image. The package carries build CPH2739_11_A.26, runs Android 16 with ColorOS 16, and is a ZIP (OFP package) download of 5.8 GB. It is the right file when the phone hangs on the logo, restarts during calls or shows a system UI error after an update.
If any step feels unclear, stop at the warning and ask before continuing rather than guessing. The whole process usually takes fifteen to twenty five minutes on a healthy USB 2.0 port.
Downloads for the PC
Use the versions listed here unless the brand support page says otherwise. Mixing an old flashing tool with a new bootloader is the usual reason a flash fails at the first partition.
| Item | Version | Purpose |
|---|---|---|
| USB driver | OPPO USB Driver 3.0.0 | Lets Windows recognise the phone in download or fastboot mode. |
| Flashing tool | SP Flash Tool v5.2 | Writes the firmware partitions and checks the package signature. |
| Archive tool | 7-Zip 24.08 | Extracts tar, tgz and zip packages without corrupting them. |
| PC requirements | Windows 10 or 11, 8 GB RAM, 15 GB free disk | Enough space for the archive, the extraction and the log files. |
Firmware details at a glance
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | OPPO |
| Model number | CPH2739 |
| Device | Reno 14 |
| Android version | Android 16 |
| OS version | ColorOS 16 |
| Firmware version | CPH2739_11_A.26 |
| Build number | CPH2739_11_A.26 |
| Region / CSC | MY (Malaysia) |
| Security patch | September 2026 |
| Firmware type | Official OFP Firmware |
| File format | ZIP (OFP package) |
| File size | 5.8 GB |
| Package contents | boot, system, vendor and modem images with an OFP manifest |
| SHA-256 | ac55614db13e33a1686dc454f84a2ece725ee76c94b9f24cf68cacde9dab7445 |
Where to download Reno 14 firmware
Package CPH2739_11_A.26 is distributed as a ZIP (OFP package) of 5.8 GB for Malaysia. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
OPPO official firmware and safe software support guide
No Google Drive mirror is published for this build. Third party mirrors often carry modified files, so use the official package and verify the SHA-256 value.
Load the scatter file or OFP package in SP Flash Tool v5.2, select download only for an update and firmware upgrade for a full repair.
Firmware highlights
None of these changes alter the layout of the home screen, but several of them affect stability, heat and battery life.
- The package includes updated vendor blobs, which often fixes Bluetooth pairing problems on older builds.
- Touch response and proximity sensor behaviour during calls are recalibrated in this release.
- Camera stability in low light and video recording at 1080p are the two areas the changelog mentions most often.
- Security patch level is September 2026, which covers the vulnerabilities listed in that month's Android bulletin.
- Battery drain reports that followed the previous patch are addressed in this build, according to the changelog summary.
- Charging behaviour at low battery percentages is tuned to reduce heat during fast charging.
Fixes for common flashing errors
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| Battery drains faster than before | Give the phone three charge cycles to settle, then check battery usage for a background app that is holding the device awake. |
| The tool cannot see the phone at all | Check Device Manager for an unknown device, reinstall the driver and try a cable that supports data rather than charging only. |
| No network service after the flash | The region code does not match the SIM. Flash the package for your country, or restore the modem backup if you made one. |
| Checksum error during extraction | The download is incomplete. Delete it, clear the browser cache and download the archive again before extracting. |
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Step by step flashing guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install OPPO USB Driver 3.0.0 and extract SP Flash Tool v5.2 and the firmware archive on the PC.
- Open the scatter file inside the package if the tool asks for one. For OFP packages, load the .ofp file directly.
- Power off the phone and remove the SIM tray if the model requires it.
- Hold Volume Up and connect the USB cable to enter download or EDL mode. The tool should detect the port.
- Select Download Only for an update that keeps data, or Firmware Upgrade for a full repair.
- Press Download or Start and wait while the tool writes the partitions.
- Do not touch the phone until the tool reports a green success message.
- Disconnect the cable and hold Power for ten seconds if the phone does not restart by itself.
- Check the build number in Settings after the first boot to confirm the flash worked.
Screens to compare
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: reno-14-cph2739-about-phone.svg | Alt text: OPPO Reno 14 CPH2739 about phone screenshot
File name: reno-14-cph2739-software-information.svg | Alt text: OPPO Reno 14 CPH2739 software information screenshot
File name: reno-14-cph2739-firmware-package.svg | Alt text: OPPO Reno 14 CPH2739 firmware package screenshot
File name: reno-14-cph2739-flashing-tool.svg | Alt text: OPPO Reno 14 CPH2739 flashing tool screenshot
Before you download: compatibility
Compatibility is decided by the model code, not by the name printed on the box. Read this list before you connect the phone.
- CPH2739 only. The package checks the model string before it writes anything, and a mismatch stops the flash.
- Dual SIM versions sold as CPH2739 (export set) use the same system image and are covered by this build.
- Regional codes EX (Global export), IN (India), ID (Indonesia), TH (Thailand) share the same hardware, but flashing a different CSC changes carrier settings and may disable local features.
- Do not flash a 5G variant with this package. The modem firmware and partition table are different.
- Carrier locked units should stay on the CSC that matches the SIM lock, otherwise the phone may ask for a network code after boot.
Firmware FAQ
How do I confirm the Android version after flashing?
Open Settings, About phone and check the Android version and build number. They should read Android 16 and CPH2739_11_A.26.
Does it work on the dual SIM version?
Yes, the CPH2739 (export set) variant uses the same system image. The model check may still display the single SIM name, which is normal.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.
Does this fix IMEI or network problems?
It restores the software side of the modem, which fixes many network problems. It cannot repair a missing IMEI caused by hardware damage or illegal modification.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.
Can I flash only the system file?
A repair install needs every image in the archive. Writing a single system file often leaves the modem and regional settings untouched, so the phone can boot with the old faults still in place.