OPPO Reno 13 CPH2689 Firmware Download - CPH2689_11_A.39 (Android 15)
OPPO Reno 13 | CPH2689 | Updated November 2026

If a factory reset and a cache wipe have already failed, the next step for the Reno 13 is a complete Android 15 stock firmware install using SP Flash Tool v5.2. Firmware version CPH2689_11_A.39 is a complete ZIP (OFP package) of 5.1 GB, so it can repair a phone that no longer boots into the system. Flashing this build restores the system, vendor and boot partitions to the exact state OPPO shipped for this model.
If the phone still boots, write down the current build number before you start so you can compare it afterwards. A slow first boot of five to ten minutes is normal after a full firmware write.
Firmware specification table
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | OPPO |
| Model number | CPH2689 |
| Device | Reno 13 |
| Android version | Android 15 |
| OS version | ColorOS 15 |
| Firmware version | CPH2689_11_A.39 |
| Build number | CPH2689_11_A.39 |
| Region / CSC | PH (Philippines) |
| Security patch | October 2026 |
| Firmware type | Official OFP Firmware |
| File format | ZIP (OFP package) |
| File size | 5.1 GB |
| Package contents | boot, system, vendor and modem images with an OFP manifest |
| SHA-256 | af205113452fc184bd3d583292f3b0a96b48a466fcd9cb28c788735883e14f77 |
What is new in this build
The build is a maintenance release at heart, and most of the work sits under the hood rather than in the visible interface.
- The boot image is signed, so the phone stays on the official verified boot chain after flashing.
- Security patch level is October 2026, which covers the vulnerabilities listed in that month's Android bulletin.
- Network switching between 4G and 5G has been adjusted for carriers in Philippines.
- Runs Android 15 with ColorOS 15 on top, matching the firmware branch that shipped for this model.
- Wi-Fi calling and VoLTE profiles for Philippines operators are included in the regional data.
- App launch time and memory management changes are rolled into this build alongside the security patch.
Error messages and what they mean
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| No network service after the flash | The region code does not match the SIM. Flash the package for your country, or restore the modem backup if you made one. |
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| Phone stays in EDL mode after the flash | Hold Power for twenty seconds, then charge the phone for ten minutes before trying to start it normally. |
| The write reaches 99 percent and freezes | Wait five minutes, then check the log. If no partition is progressing, stop the tool, reconnect and flash again with a different USB port. |
| The OFP package is rejected as invalid | Use the latest OFP extractor and confirm that the package is for CPH2689, not for a carrier variant with a different suffix. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Where to download Reno 13 firmware
Package CPH2689_11_A.39 is distributed as a ZIP (OFP package) of 5.1 GB for Philippines. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
this OPPO firmware and recovery guide
No Google Drive mirror is published for this build. Third party mirrors often carry modified files, so use the official package and verify the SHA-256 value.
Load the scatter file or OFP package in SP Flash Tool v5.2, select download only for an update and firmware upgrade for a full repair.
Firmware file structure
The archive is not a single file. Knowing which image does what helps you understand why a partial flash can leave the phone half working.
| Image | Approx. size | Purpose |
|---|---|---|
| boot.img | 0.10 GB | Kernel and ramdisk used during startup. |
| system.img | 2.45 GB | Android system, preinstalled apps and framework files. |
| vendor.img | 1.12 GB | Hardware libraries, camera and modem interfaces. |
| product.img | 0.71 GB | Regional apps, themes and carrier customisation. |
| modem.img | 0.15 GB | Radio firmware for the Philippines network bands. |
Extracted sizes vary by region and by the compression method used. The numbers above are close estimates for this 5.1 GB package, not a guarantee.
Flashing the stock ROM
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install OPPO USB Driver 3.0.0 and extract SP Flash Tool v5.2 and the firmware archive on the PC.
- Open the scatter file inside the package if the tool asks for one. For OFP packages, load the .ofp file directly.
- Power off the phone and remove the SIM tray if the model requires it.
- Hold Volume Up and connect the USB cable to enter download or EDL mode. The tool should detect the port.
- Select Download Only for an update that keeps data, or Firmware Upgrade for a full repair.
- Press Download or Start and wait while the tool writes the partitions.
- Do not touch the phone until the tool reports a green success message.
- Disconnect the cable and hold Power for ten seconds if the phone does not restart by itself.
- Check the build number in Settings after the first boot to confirm the flash worked.
Confirm the install worked
A successful write is only half the job. These checks catch the small problems that are easier to fix before you rely on the phone again.
- Open Settings, About phone and confirm the build number matches CPH2689_11_A.39.
- Test calls, mobile data, Wi-Fi and Bluetooth before you restore your apps.
- Check that the fingerprint sensor and face unlock still work. A clean flash usually keeps them, but it is worth confirming.
- Run the camera in photo and video mode for a minute to make sure the image stabilisation initialises.
- Restore your backup only after the phone has settled for ten minutes, otherwise the restore competes with background setup.
If the build number still shows the old value, the flash did not complete. Repeat the process with a fresh extraction rather than flashing the same half unpacked folder again.
Region codes for this model
OPPO ships the same hardware with different regional packages. The CSC or region code decides which carrier profiles, languages and update servers the phone uses after flashing.
| Code | Region | Build |
|---|---|---|
| EX | Global export | CPH2689_11_A.38 |
| IN | India | CPH2689_11_A.37 |
| ID | Indonesia | CPH2689_11_A.36 |
| TH | Thailand | CPH2689_11_A.35 |
| MY | Malaysia | CPH2689_11_A.34 |
| PH | Philippines | CPH2689_11_A.39 |
The bold row is the package described on this page. If you are repairing a phone for use in another country, choose the row that matches the SIM you will actually use.
Screenshot checklist
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: reno-13-cph2689-about-phone.svg | Alt text: OPPO Reno 13 CPH2689 about phone screenshot
File name: reno-13-cph2689-software-information.svg | Alt text: OPPO Reno 13 CPH2689 software information screenshot
File name: reno-13-cph2689-firmware-package.svg | Alt text: OPPO Reno 13 CPH2689 firmware package screenshot
File name: reno-13-cph2689-flashing-tool.svg | Alt text: OPPO Reno 13 CPH2689 flashing tool screenshot
Answers before you flash
The file size looks different from the listing. What now?
Compare the SHA-256 value rather than the size in megabytes. Different browsers report compressed sizes slightly differently, but the hash must match exactly.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
How do I confirm the Android version after flashing?
Open Settings, About phone and check the Android version and build number. They should read Android 15 and CPH2689_11_A.39.
Will flashing erase my data?
A full flash wipes the internal storage. If you choose the keep data option in the flashing tool, your files can survive, but a backup is still the safer choice.
Can I downgrade to an older build?
Only if the bootloader revision on the package is equal or newer than the one already on the phone. Older revision numbers are rejected at the verification stage.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.