Motorola Moto Razr 50 Ultra XT2453 Flash File Download - Official Android 14 Firmware XT2453_RTMB31.Q3-72-57-8
Motorola Moto Razr 50 Ultra | XT2453 | Updated November 2026

If the Moto Razr 50 Ultra has started restarting on its own, dropping mobile data or refusing to open the camera, the clean Android 14 package below is the shortest route back to a working phone. The build string to match is XT2453_RTMB31.Q3-72-57-8; the package is 3.8 GB and covers the RETEU region. Use it to recover a soft brick, roll back a broken update, fix persistent system errors or prepare the phone for resale.
Keep the extracted folder on the PC until the phone has booted normally at least once. Read the compatibility section before downloading, because the model code matters more than the marketing name. Do not unplug the cable while the progress bar is moving, even if the tool appears frozen for a minute.
Screenshot checklist
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: moto-razr-50-ultra-xt2453-about-phone.svg | Alt text: Motorola Moto Razr 50 Ultra XT2453 about phone screenshot
File name: moto-razr-50-ultra-xt2453-software-information.svg | Alt text: Motorola Moto Razr 50 Ultra XT2453 software information screenshot
File name: moto-razr-50-ultra-xt2453-firmware-package.svg | Alt text: Motorola Moto Razr 50 Ultra XT2453 firmware package screenshot
File name: moto-razr-50-ultra-xt2453-flashing-tool.svg | Alt text: Motorola Moto Razr 50 Ultra XT2453 flashing tool screenshot
Download Moto Razr 50 Ultra firmware
Package XT2453_RTMB31.Q3-72-57-8 is distributed as a ZIP (XML fastboot package) of 3.8 GB for Europe. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
Motorola official firmware and safe software support guide
If the download stops halfway, delete the partial file and start again. A truncated archive is the most common cause of a checksum error in RSD Lite.
Unpack the ZIP, keep the folder structure intact and either run the included flash script or load the XML package in RSD Lite and press Start.
Step by step flashing guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install Motorola Device Manager 2.5.4, then extract the fastboot package with 7-Zip. RSD Lite or the bundled script can write it.
- Install Android platform tools if you plan to flash with fastboot commands instead of RSD Lite.
- Power off the phone, then hold Volume Down and Power to enter fastboot mode.
- Connect the cable and confirm the device appears with fastboot devices.
- Open flashfile.xml to see the partition list, or load the package in RSD Lite.
- Run the provided flash script. It writes boot, system, vendor and modem in sequence.
- Do not lock the bootloader unless the package specifically includes the lock command.
- Wait for the script to finish and the phone to reboot.
- If the phone stays in fastboot, run the script again from the beginning rather than skipping a partition.
Fixes for common flashing errors
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| Fastboot reports a partition error | The package and the phone have different partition tables. Confirm the model with fastboot getvar all before flashing anything else. |
| Checksum error during extraction | The download is incomplete. Delete it, clear the browser cache and download the archive again before extracting. |
| RSD Lite says failed flashing process | Reinstall Motorola Device Manager 2.5.4, close any other phone software, and run RSD Lite as administrator with the package extracted to a short path. |
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| Hab check failed for boot | The boot image is not signed for this device. Use the untouched XML package and do not mix images from another build. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Firmware specification table
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | Motorola |
| Model number | XT2453 |
| Device | Moto Razr 50 Ultra |
| Android version | Android 14 |
| OS version | My UX |
| Firmware version | XT2453_RTMB31.Q3-72-57-8 |
| Build number | XT2453_RTMB31.Q3-72-57-8 |
| Region / CSC | RETEU (Europe) |
| Security patch | May 2026 |
| Firmware type | Official Fastboot Firmware |
| File format | ZIP (XML fastboot package) |
| File size | 3.8 GB |
| Package contents | boot, system, vendor, modem and gpt images with flashfile.xml |
| SHA-256 | 4f50013dc811f2a7d679797add24dc05b2530ff0c5fc0050393b343189534666 |
Answers before you flash
Does it work on the dual SIM version?
Yes, the XT2453-1 variant uses the same system image. The model check may still display the single SIM name, which is normal.
Can I flash only the system file?
A repair install needs every image in the archive. Writing a single system file often leaves the modem and regional settings untouched, so the phone can boot with the old faults still in place.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.
Is this XT2453_RTMB31.Q3-72-57-8 firmware official?
Yes. The package is a signed official fastboot firmware released for the XT2453, and it is the same file an authorised service centre would use for a software reinstall.
Can I install this firmware without a PC?
No. Motorola RSD Lite 6.2.4 or fastboot needs a Windows computer and a USB cable. OTA updates are different, but this package is a complete image that has to be written from a PC.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.