Huawei P Smart Z STK-LX1 Stock Firmware STK-LX1 10.0.0.125(C10E7R2P1) Download - Android 10
Huawei P Smart Z | STK-LX1 | Updated November 2026
The Huawei P Smart Z (STK-LX1) is one of those phones that works perfectly until an update stalls halfway, and then refuses to get past the logo. It is a full ZIP (dload with UPDATE.APP) image of 4.4 GB, not a small OTA, so the phone must be at or below the bootloader revision named in the file. Because it is a full image, it also fixes problems that a factory reset cannot touch, such as a damaged system partition.
Read the compatibility section before downloading, because the model code matters more than the marketing name. Do not unplug the cable while the progress bar is moving, even if the tool appears frozen for a minute.
Firmware information
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | Huawei |
| Model number | STK-LX1 |
| Device | P Smart Z |
| Android version | Android 10 |
| OS version | EMUI 10.0 |
| Firmware version | STK-LX1 10.0.0.125(C10E7R2P1) |
| Build number | STK-LX1 10.0.0.125(C10E7R2P1) |
| Region / CSC | C10 (Russia) |
| Security patch | April 2023 |
| Firmware type | Official dload Firmware |
| File format | ZIP (dload with UPDATE.APP) |
| File size | 4.4 GB |
| Package contents | UPDATE.APP, cust and preload images with a version manifest |
| SHA-256 | 9ed659da87221389cc5dc20099422e78199678061c971400f299590508ebc207 |
Get the STK-LX1 firmware package
Package STK-LX1 10.0.0.125(C10E7R2P1) is distributed as a ZIP (dload with UPDATE.APP) of 4.4 GB for Russia. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
the official Huawei firmware support page
No Google Drive mirror is published for this build. Third party mirrors often carry modified files, so use the official package and verify the SHA-256 value.
Copy the dload folder to a formatted SD card or use DC-Phoenix, then let the phone verify UPDATE.APP before it installs.
Step by step flashing guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install Huawei HiSuite 11.0.0 and Huawei DC-Phoenix 1.0.0.8 on the PC.
- Extract the firmware ZIP. Inside you should find an UPDATE.APP file and a dload folder structure.
- Copy the dload folder to the root of a formatted SD card, or connect the phone in HiSuite mode.
- On the phone, open Settings, System and update, then choose local update if the option is available.
- If the phone cannot boot, hold Volume Up and Volume Down while pressing Power to trigger the forced dload install.
- Wait while the phone verifies UPDATE.APP. This can take several minutes and the screen may stay at 5 percent.
- Do not remove the SD card or cable until the progress bar reaches 100 percent and the phone restarts.
- After the first boot, check the build number and confirm that the regional cust partition was installed.
Error messages and what they mean
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| Cust partition mismatch after the flash | The package includes a cust image for another region. Flash the correct regional dload package to restore carrier settings. |
| Phone boots straight to recovery after flashing | The data partition is encrypted with the old key. Perform a factory reset from recovery, then let the phone rebuild the partition. |
| Battery drains faster than before | Give the phone three charge cycles to settle, then check battery usage for a background app that is holding the device awake. |
| The write reaches 99 percent and freezes | Wait five minutes, then check the log. If no partition is progressing, stop the tool, reconnect and flash again with a different USB port. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Screenshot checklist
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: p-smart-z-stk-lx1-about-phone.svg | Alt text: Huawei P Smart Z STK-LX1 about phone screenshot
File name: p-smart-z-stk-lx1-software-information.svg | Alt text: Huawei P Smart Z STK-LX1 software information screenshot
File name: p-smart-z-stk-lx1-firmware-package.svg | Alt text: Huawei P Smart Z STK-LX1 firmware package screenshot
File name: p-smart-z-stk-lx1-flashing-tool.svg | Alt text: Huawei P Smart Z STK-LX1 flashing tool screenshot
Answers before you flash
Can I install this firmware without a PC?
No. Huawei DC-Phoenix 1.0.0.8 needs a Windows computer and a USB cable. OTA updates are different, but this package is a complete image that has to be written from a PC.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
How do I confirm the Android version after flashing?
Open Settings, About phone and check the Android version and build number. They should read Android 10 and STK-LX1 10.0.0.125(C10E7R2P1).
Can I downgrade to an older build?
Only if the bootloader revision on the package is equal or newer than the one already on the phone. Older revision numbers are rejected at the verification stage.
Is this STK-LX1 10.0.0.125(C10E7R2P1) firmware official?
Yes. The package is a signed official dload firmware released for the STK-LX1, and it is the same file an authorised service centre would use for a software reinstall.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.