TECNO Pova Neo 4 LH7 Firmware LH7-H131CDPB-260623V948 Free Download (Android 15 Stock ROM)
TECNO Pova Neo 4 | LH7 | Updated November 2026
If a factory reset and a cache wipe have already failed, the next step for the Pova Neo 4 is a complete Android 15 stock firmware install using SP Flash Tool v5.2. This is the PK variant of LH7-H131CDPB-260623V948, a ZIP with scatter file of 2.3 GB that contains every partition needed for a clean install. It is intended for software repair only, not for bypassing account locks, carrier restrictions or security features.
If any step feels unclear, stop at the warning and ask before continuing rather than guessing. If the phone still boots, write down the current build number before you start so you can compare it afterwards.
Before and after screens
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: pova-neo-4-lh7-about-phone.svg | Alt text: TECNO Pova Neo 4 LH7 about phone screenshot
File name: pova-neo-4-lh7-software-information.svg | Alt text: TECNO Pova Neo 4 LH7 software information screenshot
File name: pova-neo-4-lh7-firmware-package.svg | Alt text: TECNO Pova Neo 4 LH7 firmware package screenshot
File name: pova-neo-4-lh7-flashing-tool.svg | Alt text: TECNO Pova Neo 4 LH7 flashing tool screenshot
Download Pova Neo 4 firmware
Package LH7-H131CDPB-260623V948 is distributed as a ZIP with scatter file of 2.3 GB for Pakistan. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
the official TECNO firmware support page
No Google Drive mirror is published for this build. Third party mirrors often carry modified files, so use the official package and verify the SHA-256 value.
Load the scatter file in SP Flash Tool v5.2, tick only the partitions you need and choose Download Only for an update or Firmware Upgrade for a full repair.
Firmware installation guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install TECNO USB Driver 1.0.4 and MediaTek VCOM and extract both SP Flash Tool v5.2 and the firmware ZIP.
- Open SP Flash Tool, click the scatter loading button and choose the scatter file from the extracted folder.
- Confirm that boot, system, vendor and userdata are ticked. Leave preloader ticked only for a full repair.
- Switch to the Download tab and choose Download Only or Firmware Upgrade.
- Power off the phone, then hold Volume Up or Volume Down while connecting USB, depending on the model.
- Wait for the tool to detect the MediaTek port and begin writing.
- Keep the cable connected until the green circle appears and the tool reports Download OK.
- Disconnect the phone and hold Power for fifteen seconds. The logo should appear within a minute.
- If the tool stops at DA download, reinstall the VCOM driver and try another USB port.
When the flash fails
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| SP Flash Tool shows a DA download error | Install the MediaTek VCOM driver again, hold Volume Up while connecting, and disable driver signature enforcement before retrying. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
| Invalid scatter file in SP Flash Tool | Point the tool at the scatter file inside the extracted folder, not at the ZIP, and make sure the file was not renamed. |
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| The tool cannot see the phone at all | Check Device Manager for an unknown device, reinstall the driver and try a cable that supports data rather than charging only. |
| Stuck on the brand logo after a successful flash | Boot to recovery, wipe cache and data, then restart. If it still fails, the package may be for a different regional variant. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Complete firmware details
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | TECNO |
| Model number | LH7 |
| Device | Pova Neo 4 |
| Android version | Android 15 |
| OS version | HiOS 14.0 |
| Firmware version | LH7-H131CDPB-260623V948 |
| Build number | LH7-H131CDPB-260623V948 |
| Region / CSC | PK (Pakistan) |
| Security patch | June 2026 |
| Firmware type | Official Stock ROM |
| File format | ZIP with scatter file |
| File size | 2.3 GB |
| Package contents | boot, system, vendor, userdata and preloader images with a scatter file |
| SHA-256 | 203f85e8a9b71395e06399ea46308cf55c37661faea3305a93792080ddef343c |
Questions about this firmware
Is this LH7-H131CDPB-260623V948 firmware official?
Yes. The package is a signed official stock rom released for the LH7, and it is the same file an authorised service centre would use for a software reinstall.
Can I downgrade to an older build?
Only if the bootloader revision on the package is equal or newer than the one already on the phone. Older revision numbers are rejected at the verification stage.
Does this fix IMEI or network problems?
It restores the software side of the modem, which fixes many network problems. It cannot repair a missing IMEI caused by hardware damage or illegal modification.
Can I flash only the system file?
A repair install needs every image in the archive. Writing a single system file often leaves the modem and regional settings untouched, so the phone can boot with the old faults still in place.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.
Which flashing tool version should I use?
SP Flash Tool v5.2 is the version that matches this build. Newer tools usually work, but avoid very old releases because they may not recognise the partition layout.
How long does the first boot take?
Expect five to ten minutes. The phone rebuilds the runtime cache and verifies the system partition, so a slow first start is normal.