V2057 Firmware Download - Vivo Y52s Android 12 PD2057F_EX_A_12.0.4.7.W28
Vivo Y52s | V2057 | Updated November 2026
Owners of the Vivo Y52s often find this page after a repair shop quotes more than the phone is worth, which is exactly the situation a stock firmware reinstall is designed for. Published for Malaysia, the 5.4 GB package includes Funtouch OS 12 on top of Android 12 and the February 2026 security update. Because it is a full image, it also fixes problems that a factory reset cannot touch, such as a damaged system partition.
Do not unplug the cable while the progress bar is moving, even if the tool appears frozen for a minute. Read the compatibility section before downloading, because the model code matters more than the marketing name.
What the update changes
None of these changes alter the layout of the home screen, but several of them affect stability, heat and battery life.
- Charging behaviour at low battery percentages is tuned to reduce heat during fast charging.
- Battery drain reports that followed the previous patch are addressed in this build, according to the changelog summary.
- The package is a full ZIP (PD firmware package) image, not an incremental OTA, so it repairs partition level corruption as well.
- App launch time and memory management changes are rolled into this build alongside the security patch.
- Camera stability in low light and video recording at 1080p are the two areas the changelog mentions most often.
- Network switching between 4G and 5G has been adjusted for carriers in Malaysia.
Post flash checklist
A successful write is only half the job. These checks catch the small problems that are easier to fix before you rely on the phone again.
- Open Settings, About phone and confirm the build number matches PD2057F_EX_A_12.0.4.7.W28.
- Test calls, mobile data, Wi-Fi and Bluetooth before you restore your apps.
- Check that the fingerprint sensor and face unlock still work. A clean flash usually keeps them, but it is worth confirming.
- Run the camera in photo and video mode for a minute to make sure the image stabilisation initialises.
- Restore your backup only after the phone has settled for ten minutes, otherwise the restore competes with background setup.
If the build number still shows the old value, the flash did not complete. Repeat the process with a fresh extraction rather than flashing the same half unpacked folder again.
Firmware information
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | Vivo |
| Model number | V2057 |
| Device | Y52s |
| Android version | Android 12 |
| OS version | Funtouch OS 12 |
| Firmware version | PD2057F_EX_A_12.0.4.7.W28 |
| Build number | PD2057F_EX_A_12.0.4.7.W28 |
| Region / CSC | MY (Malaysia) |
| Security patch | February 2026 |
| Firmware type | Official PD Firmware |
| File format | ZIP (PD firmware package) |
| File size | 5.4 GB |
| Package contents | boot, system, vendor and modem images with a scatter file |
| SHA-256 | c23659a467ce9787e47c8831a1f5a2c378cdfc454c53e84ae5c7a2ad3c1c5642 |
Download Y52s firmware
Package PD2057F_EX_A_12.0.4.7.W28 is distributed as a ZIP (PD firmware package) of 5.4 GB for Malaysia. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
The link above opens the brand level support page, where the package is described together with the safety notes. Keep that page open while you flash.
Load the scatter file or OFP package in SP Flash Tool v5.2, select download only for an update and firmware upgrade for a full repair.
Common installation errors and fixes
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
| No network service after the flash | The region code does not match the SIM. Flash the package for your country, or restore the modem backup if you made one. |
| Phone boots straight to recovery after flashing | The data partition is encrypted with the old key. Perform a factory reset from recovery, then let the phone rebuild the partition. |
| The write reaches 99 percent and freezes | Wait five minutes, then check the log. If no partition is progressing, stop the tool, reconnect and flash again with a different USB port. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Firmware installation guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install vivo USB Driver 1.0.8 and extract SP Flash Tool v5.2 and the firmware archive on the PC.
- Open the scatter file inside the package if the tool asks for one. For OFP packages, load the .ofp file directly.
- Power off the phone and remove the SIM tray if the model requires it.
- Hold Volume Up and connect the USB cable to enter download or EDL mode. The tool should detect the port.
- Select Download Only for an update that keeps data, or Firmware Upgrade for a full repair.
- Press Download or Start and wait while the tool writes the partitions.
- Do not touch the phone until the tool reports a green success message.
- Disconnect the cable and hold Power for ten seconds if the phone does not restart by itself.
- Check the build number in Settings after the first boot to confirm the flash worked.
Choose the right region
Vivo ships the same hardware with different regional packages. The CSC or region code decides which carrier profiles, languages and update servers the phone uses after flashing.
| Code | Region | Build |
|---|---|---|
| EX | Global export | PD2057F_EX_A_12.0.4.7.W27 |
| IN | India | PD2057F_EX_A_12.0.4.7.W26 |
| ID | Indonesia | PD2057F_EX_A_12.0.4.7.W25 |
| TH | Thailand | PD2057F_EX_A_12.0.4.7.W24 |
| MY | Malaysia | PD2057F_EX_A_12.0.4.7.W28 |
| PH | Philippines | PD2057F_EX_A_12.0.4.7.W22 |
The bold row is the package described on this page. If you are repairing a phone for use in another country, choose the row that matches the SIM you will actually use.
Inside the firmware package
The archive is not a single file. Knowing which image does what helps you understand why a partial flash can leave the phone half working.
| Image | Approx. size | Purpose |
|---|---|---|
| boot.img | 0.11 GB | Kernel and ramdisk used during startup. |
| system.img | 2.59 GB | Android system, preinstalled apps and framework files. |
| vendor.img | 1.19 GB | Hardware libraries, camera and modem interfaces. |
| product.img | 0.76 GB | Regional apps, themes and carrier customisation. |
| modem.img | 0.16 GB | Radio firmware for the Malaysia network bands. |
Extracted sizes vary by region and by the compression method used. The numbers above are close estimates for this 5.4 GB package, not a guarantee.
Firmware FAQ
Will flashing erase my data?
A full flash wipes the internal storage. If you choose the keep data option in the flashing tool, your files can survive, but a backup is still the safer choice.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.
Why does my phone show a different region after flashing?
The CSC or region code in the package decides that. Flash the build for the country where you use the phone if you want local carrier features and update servers.
Does this fix IMEI or network problems?
It restores the software side of the modem, which fixes many network problems. It cannot repair a missing IMEI caused by hardware damage or illegal modification.
Does it work on the dual SIM version?
Yes, the V2057 (PD variant) variant uses the same system image. The model check may still display the single SIM name, which is normal.
The file size looks different from the listing. What now?
Compare the SHA-256 value rather than the size in megabytes. Different browsers report compressed sizes slightly differently, but the hash must match exactly.