OPPO Reno 4 Firmware Download CPH2089_11_A.20 - CPH2089 Android 11 Stock ROM
OPPO Reno 4 | CPH2089 | Updated November 2026
The OPPO Reno 4 has been around since 2020, and the Android 11 build described here is the latest complete package published for the CPH2089. Inside the archive you get boot, system, vendor and modem images with an OFP manifest, and the download is 5.5 GB. Because it is a full image, it also fixes problems that a factory reset cannot touch, such as a damaged system partition.
Keep the extracted folder on the PC until the phone has booted normally at least once. Read the compatibility section before downloading, because the model code matters more than the marketing name. The whole process usually takes fifteen to twenty five minutes on a healthy USB 2.0 port.
Changes in this firmware
This is not a cosmetic update. The changelog touches security, modem behaviour and the parts of the system that tend to fail after two or three years of use.
- Wi-Fi calling and VoLTE profiles for India operators are included in the regional data.
- The boot image is signed, so the phone stays on the official verified boot chain after flashing.
- Battery drain reports that followed the previous patch are addressed in this build, according to the changelog summary.
- App launch time and memory management changes are rolled into this build alongside the security patch.
- Network switching between 4G and 5G has been adjusted for carriers in India.
- Touch response and proximity sensor behaviour during calls are recalibrated in this release.
Checks after installation
A successful write is only half the job. These checks catch the small problems that are easier to fix before you rely on the phone again.
- Open Settings, About phone and confirm the build number matches CPH2089_11_A.20.
- Test calls, mobile data, Wi-Fi and Bluetooth before you restore your apps.
- Check that the fingerprint sensor and face unlock still work. A clean flash usually keeps them, but it is worth confirming.
- Run the camera in photo and video mode for a minute to make sure the image stabilisation initialises.
- Restore your backup only after the phone has settled for ten minutes, otherwise the restore competes with background setup.
If the build number still shows the old value, the flash did not complete. Repeat the process with a fresh extraction rather than flashing the same half unpacked folder again.
CSC and region guide
OPPO ships the same hardware with different regional packages. The CSC or region code decides which carrier profiles, languages and update servers the phone uses after flashing.
| Code | Region | Build |
|---|---|---|
| EX | Global export | CPH2089_11_A.19 |
| IN | India | CPH2089_11_A.20 |
| ID | Indonesia | CPH2089_11_A.17 |
| TH | Thailand | CPH2089_11_A.16 |
| MY | Malaysia | CPH2089_11_A.15 |
| PH | Philippines | CPH2089_11_A.14 |
The bold row is the package described on this page. If you are repairing a phone for use in another country, choose the row that matches the SIM you will actually use.
Get the CPH2089 firmware package
Package CPH2089_11_A.20 is distributed as a ZIP (OFP package) of 5.5 GB for India. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
the official OPPO firmware support page
No Google Drive mirror is published for this build. Third party mirrors often carry modified files, so use the official package and verify the SHA-256 value.
Load the scatter file or OFP package in SP Flash Tool v5.2, select download only for an update and firmware upgrade for a full repair.
Firmware specification table
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | OPPO |
| Model number | CPH2089 |
| Device | Reno 4 |
| Android version | Android 11 |
| OS version | ColorOS 11 |
| Firmware version | CPH2089_11_A.20 |
| Build number | CPH2089_11_A.20 |
| Region / CSC | IN (India) |
| Security patch | December 2023 |
| Firmware type | Official OFP Firmware |
| File format | ZIP (OFP package) |
| File size | 5.5 GB |
| Package contents | boot, system, vendor and modem images with an OFP manifest |
| SHA-256 | 19b2f0a03d252f856ebfe547eb397e419e152e5f19b3087badb482e4de8c7d30 |
Step by step flashing guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install OPPO USB Driver 3.0.0 and extract SP Flash Tool v5.2 and the firmware archive on the PC.
- Open the scatter file inside the package if the tool asks for one. For OFP packages, load the .ofp file directly.
- Power off the phone and remove the SIM tray if the model requires it.
- Hold Volume Up and connect the USB cable to enter download or EDL mode. The tool should detect the port.
- Select Download Only for an update that keeps data, or Firmware Upgrade for a full repair.
- Press Download or Start and wait while the tool writes the partitions.
- Do not touch the phone until the tool reports a green success message.
- Disconnect the cable and hold Power for ten seconds if the phone does not restart by itself.
- Check the build number in Settings after the first boot to confirm the flash worked.
Firmware file structure
The archive is not a single file. Knowing which image does what helps you understand why a partial flash can leave the phone half working.
| Image | Approx. size | Purpose |
|---|---|---|
| boot.img | 0.11 GB | Kernel and ramdisk used during startup. |
| system.img | 2.64 GB | Android system, preinstalled apps and framework files. |
| vendor.img | 1.21 GB | Hardware libraries, camera and modem interfaces. |
| product.img | 0.77 GB | Regional apps, themes and carrier customisation. |
| modem.img | 0.16 GB | Radio firmware for the India network bands. |
Extracted sizes vary by region and by the compression method used. The numbers above are close estimates for this 5.5 GB package, not a guarantee.
Common installation errors and fixes
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| Battery drains faster than before | Give the phone three charge cycles to settle, then check battery usage for a background app that is holding the device awake. |
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
| Checksum error during extraction | The download is incomplete. Delete it, clear the browser cache and download the archive again before extracting. |
| SP Flash Tool shows a DA download error | Install the MediaTek VCOM driver again, hold Volume Up while connecting, and disable driver signature enforcement before retrying. |
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Questions about this firmware
Can I flash only the system file?
A repair install needs every image in the archive. Writing a single system file often leaves the modem and regional settings untouched, so the phone can boot with the old faults still in place.
Is a Google Drive mirror available?
Not for this build. Use the official brand support page linked above. Mirror copies are often repacked and cannot be trusted for a repair.
Is this CPH2089_11_A.20 firmware official?
Yes. The package is a signed official ofp firmware released for the CPH2089, and it is the same file an authorised service centre would use for a software reinstall.
Why does my phone show a different region after flashing?
The CSC or region code in the package decides that. Flash the build for the country where you use the phone if you want local carrier features and update servers.
How do I confirm the Android version after flashing?
Open Settings, About phone and check the Android version and build number. They should read Android 11 and CPH2089_11_A.20.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.
Is the bootloader unlocked by this process?
No. Flashing an official package does not unlock the bootloader, and on most OPPO models the bootloader stays locked unless you use the manufacturer's unlock programme.