Download X6815 Flash File - Infinix Zero 5G X6815-H230CBQ-251217V625 Android 12
Infinix Zero 5G | X6815 | Updated November 2026

The Infinix Zero 5G (X6815) is one of those phones that works perfectly until an update stalls halfway, and then refuses to get past the logo. It is a full ZIP with scatter file image of 3.6 GB, not a small OTA, so the phone must be at or below the bootloader revision named in the file. Technicians use this package to recover dead phones, remove test firmware and bring imported units back to the correct regional build.
If any step feels unclear, stop at the warning and ask before continuing rather than guessing. Keep the extracted folder on the PC until the phone has booted normally at least once.
Compatibility and model check
Compatibility is decided by the model code, not by the name printed on the box. Read this list before you connect the phone.
- X6815 only. The package checks the model string before it writes anything, and a mismatch stops the flash.
- Dual SIM versions sold as X6815 (Global) use the same system image and are covered by this build.
- Regional codes GL (Global), IN (India), NG (Nigeria), PK (Pakistan) share the same hardware, but flashing a different CSC changes carrier settings and may disable local features.
- Do not cross flash the 4G version of the Zero 5G. The modem firmware and partition table are different.
- Carrier locked units should stay on the CSC that matches the SIM lock, otherwise the phone may ask for a network code after boot.
Before and after screens
The images below show the screens to compare before and after flashing. Keep the same file names and alt text if you replace them with your own captures so search engines can still match them to the model.
File name: zero-5g-x6815-about-phone.svg | Alt text: Infinix Zero 5G X6815 about phone screenshot
File name: zero-5g-x6815-software-information.svg | Alt text: Infinix Zero 5G X6815 software information screenshot
File name: zero-5g-x6815-firmware-package.svg | Alt text: Infinix Zero 5G X6815 firmware package screenshot
File name: zero-5g-x6815-flashing-tool.svg | Alt text: Infinix Zero 5G X6815 flashing tool screenshot
Download the X6815 stock firmware
Package X6815-H230CBQ-251217V625 is distributed as a ZIP with scatter file of 3.6 GB for Indonesia. The same archive is used for a repair install and for a clean reinstall, so you only need to download it once.
Infinix official firmware and safe software support guide
Always confirm the model code on the download page before you start. A package built for a different variant can pass the checksum and still leave the phone without network service.
Load the scatter file in SP Flash Tool v5.2, tick only the partitions you need and choose Download Only for an update or Firmware Upgrade for a full repair.
Troubleshooting the installation
Most failed flashes fall into one of six patterns. Match the message on your screen with the table before you change anything on the phone.
| Problem | What to do |
|---|---|
| Invalid scatter file in SP Flash Tool | Point the tool at the scatter file inside the extracted folder, not at the ZIP, and make sure the file was not renamed. |
| FRP or account verification appears after setup | The phone still has the previous owner's account. Official firmware does not remove account locks; use the recovery options available to the rightful owner. |
| Proximity sensor stops working after the update | Recalibrate the sensor from the hidden service menu or flash the previous build. This is a known issue on a small number of units. |
| Stuck on the brand logo after a successful flash | Boot to recovery, wipe cache and data, then restart. If it still fails, the package may be for a different regional variant. |
| Phone heats up and reboots during the flash | Stop the process, let the phone cool for twenty minutes and use a powered USB port. Heat during a write usually means the battery is failing. |
| Phone boots straight to recovery after flashing | The data partition is encrypted with the old key. Perform a factory reset from recovery, then let the phone rebuild the partition. |
If the phone shows a hardware fault such as a swollen battery, a cracked board or liquid damage, software cannot fix it. Stop and take the device to an authorised service centre.
Step by step flashing guide
The process below is the one that matches this package. Read every step before you touch the phone, and keep the log window visible so you can see where a failure happens.
- Install Infinix USB Driver 1.0.6 and MediaTek VCOM and extract both SP Flash Tool v5.2 and the firmware ZIP.
- Open SP Flash Tool, click the scatter loading button and choose the scatter file from the extracted folder.
- Confirm that boot, system, vendor and userdata are ticked. Leave preloader ticked only for a full repair.
- Switch to the Download tab and choose Download Only or Firmware Upgrade.
- Power off the phone, then hold Volume Up or Volume Down while connecting USB, depending on the model.
- Wait for the tool to detect the MediaTek port and begin writing.
- Keep the cable connected until the green circle appears and the tool reports Download OK.
- Disconnect the phone and hold Power for fifteen seconds. The logo should appear within a minute.
- If the tool stops at DA download, reinstall the VCOM driver and try another USB port.
What the update changes
None of these changes alter the layout of the home screen, but several of them affect stability, heat and battery life.
- The boot image is signed, so the phone stays on the official verified boot chain after flashing.
- Camera stability in low light and video recording at 1080p are the two areas the changelog mentions most often.
- Build X6815-H230CBQ-251217V625 replaces older ID packages and keeps the Indonesia modem configuration intact.
- The package includes updated vendor blobs, which often fixes Bluetooth pairing problems on older builds.
- Touch response and proximity sensor behaviour during calls are recalibrated in this release.
- Network switching between 4G and 5G has been adjusted for carriers in Indonesia.
Firmware specification table
These are the details that matter before you download anything. Compare the model code and build string with the phone in your hand, not with a listing photo.
| Brand | Infinix |
| Model number | X6815 |
| Device | Zero 5G |
| Android version | Android 12 |
| OS version | XOS 8.0 |
| Firmware version | X6815-H230CBQ-251217V625 |
| Build number | X6815-H230CBQ-251217V625 |
| Region / CSC | ID (Indonesia) |
| Security patch | December 2025 |
| Firmware type | Official Stock ROM |
| File format | ZIP with scatter file |
| File size | 3.6 GB |
| Package contents | boot, system, vendor, userdata and preloader images with a scatter file |
| SHA-256 | a1584fdfd0fa1ac87917c1d424b9d0610fa7f55ffac6332bd22feb10ea6c17ba |
Frequently asked questions
Does it work on the dual SIM version?
Yes, the X6815 (Global) variant uses the same system image. The model check may still display the single SIM name, which is normal.
Can I flash only the system file?
A repair install needs every image in the archive. Writing a single system file often leaves the modem and regional settings untouched, so the phone can boot with the old faults still in place.
Can I install this firmware without a PC?
No. SP Flash Tool v5.2 needs a Windows computer and a USB cable. OTA updates are different, but this package is a complete image that has to be written from a PC.
Will this remove a Google account or FRP lock?
No. Official firmware does not bypass account verification. Only the rightful owner can remove the account through the normal recovery process.
Is the bootloader unlocked by this process?
No. Flashing an official package does not unlock the bootloader, and on most Infinix models the bootloader stays locked unless you use the manufacturer's unlock programme.
Why does my phone show a different region after flashing?
The CSC or region code in the package decides that. Flash the build for the country where you use the phone if you want local carrier features and update servers.
Do I need to root the phone first?
No. Root is not required and can actually cause the flash to fail on devices with verified boot. Use the official package on an unmodified phone.